307.422 Virtual Product Development
This course is in all assigned curricula part of the STEOP.
This course is in at least 1 assigned curriculum part of the STEOP.

2019W, UE, 2.0h, 2.0EC
TUWEL

Properties

  • Semester hours: 2.0
  • Credits: 2.0
  • Type: UE Exercise

Learning outcomes

After successful completion of the course, students are able to:

  • apply product development methods
  • use various CAx methods
  • use neutral exchange formats
  • develop simple products themselves
  • incorporate product requirements into product development

Subject of course

see corresponding lecture

Teaching methods

  • Use of CATIA V5 software as CAD software (or other CAD software)
  • Using CATIA V5 software as CAE software (or other CAE software)
  • Application of virtual product development methods (calculation, simulation, DMU, FMU)

Mode of examination

Written and oral

Additional information

to be announced

Lecturers

Contributors

Institute

Course dates

DayTimeDateLocationDescription
Mon14:00 - 16:0007.10.2019 GM 2 Radinger HSThemenvorstellung
Wed17:00 - 19:0023.10.2019 - 15.01.2020CAD-Labor Saal 3 Tutorium
Mon16:00 - 18:0028.10.2019 - 13.01.2020CAD-Labor Saal 3 Tutorium
Thu09:00 - 11:0009.01.2020 - 16.01.2020CAD-Labor Saal 3 Tutorium
Virtual Product Development - Single appointments
DayDateTimeLocationDescription
Mon07.10.201914:00 - 16:00 GM 2 Radinger HSThemenvorstellung
Wed23.10.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon28.10.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed30.10.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon04.11.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed06.11.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon11.11.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed13.11.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon18.11.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed20.11.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon25.11.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed27.11.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon02.12.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed04.12.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon09.12.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed11.12.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Mon16.12.201916:00 - 18:00CAD-Labor Saal 3 Tutorium
Wed18.12.201917:00 - 19:00CAD-Labor Saal 3 Tutorium
Wed08.01.202017:00 - 19:00CAD-Labor Saal 3 Tutorium
Thu09.01.202009:00 - 11:00CAD-Labor Saal 3 Tutorium

Examination modalities

The performance is based on the project carried out during the course.

Course registration

Begin End Deregistration end
01.10.2019 08:00 31.10.2019 00:00

Group Registration

GroupRegistration FromTo
20.01.2020 von 09:00 - 10:00 Uhr10.01.2020 08:0019.01.2020 23:55
20.01.2020 von 10:00 - 11:00 Uhr10.01.2020 08:0019.01.2020 23:55
20.01.2020 von 11:00 - 12:00 Uhr10.01.2020 08:0019.01.2020 23:55
20.01.2020 von 14:30 - 15:30 Uhr10.01.2020 08:0019.01.2020 23:55
20.01.2020 von 15:30 - 16:30 Uhr10.01.2020 08:0019.01.2020 23:55
20.01.2020 von 16:30 - 17:30 Uhr10.01.2020 08:0019.01.2020 23:55
21.01.2020 von 09:00 - 10:00 Uhr10.01.2020 08:0019.01.2020 23:55
21.01.2020 von 10:00 - 11:00 Uhr10.01.2020 08:0019.01.2020 23:55
21.01.2020 von 11:00 - 12:00 Uhr10.01.2020 08:0019.01.2020 23:55
21.01.2020 von 13:30 - 14:30 Uhr10.01.2020 08:0019.01.2020 23:55
21.01.2020 von 14:30 - 15:30 Uhr10.01.2020 08:0019.01.2020 23:55
23.01.2020 von 14:00 - 15:00 Uhr10.01.2020 08:0019.01.2020 23:55
23.01.2020 von 15:00 - 16:00 Uhr10.01.2020 08:0019.01.2020 23:55
23.01.2020 von 16:00 - 17:00 Uhr10.01.2020 08:0019.01.2020 23:55
24.01.2020 von 09:00 - 10:00 Uhr10.01.2020 08:0019.01.2020 23:55
24.01.2020 von 10:00 - 11:00 Uhr10.01.2020 08:0019.01.2020 23:55
24.01.2020 von 11:00 - 12:00 Uhr10.01.2020 08:0019.01.2020 23:55

Curricula

Study CodeObligationSemesterPrecon.Info
033 245 Mechanical Engineering Mandatory electiveSTEOP
Course requires the completion of the introductory and orientation phase
033 282 Mechanical Engineering - Management Mandatory electiveSTEOP
Course requires the completion of the introductory and orientation phase
066 445 Mechanical Engineering Mandatory electiveSTEOP
Course requires the completion of the introductory and orientation phase
066 482 Mechanical Engineering - Management Mandatory electiveSTEOP
Course requires the completion of the introductory and orientation phase

Literature

No lecture notes are available.

Accompanying courses

Language

German